Höppel, Heinz Werner

2023

• Risse JH., Trempa M., Huber F., Höppel HW., Bartels D., Schmidt M., Reimann C., Friedrich J.:
  Microstructure and Mechanical Properties of Hypereutectic Al-High Si Alloys up to 70 wt.% Si-Content Produced from Pre-Alloyed and Blended Powder via Laser Powder Bed Fusion
  In: Materials 16 (2023), S. 657
  ISSN: 1996-1944
  DOI: 10.3390/ma16020657

2022

• Arnoldt AR., Schiffl A., Höppel HW., Oesterreicher JA.:
  Influence of different homogenization heat treatments on the microstructure and hot flow stress of the aluminum alloy AA6082
  In: Materials Characterization 191 (2022)
  ISSN: 1044-5803
  DOI: 10.1016/j.matchar.2022.112129
• Diepold B., Schunk C., Kümmel F., Fey T., Prakash A., Höppel HW., Göken M.:
  Fatigue Life Optimized Layer Architecture of Ultrafine-Grained Al-Ti Laminates Under Bending Stresses
  In: Advanced Engineering Materials (2022)
  ISSN: 1438-1656
  DOI: 10.1002/adem.202101143
• Elitzer D., Jäger S., Höll C., Baier D., Varga R., Zaeh MF., Göken M., Höppel HW.:
  Development of Microstructure and Mechanical Properties of TiAl6V4 Processed by Wire and Arc Additive Manufacturing
  In: Advanced Engineering Materials (2022)
  ISSN: 1438-1656
  DOI: 10.1002/adem.202201025
• Höppel HW., May J., Eisenlohr P., Göken M.:
  Strain-rate sensitivity of ultrafine-grained materials
  In: International Journal of Materials Research 96 (2022), S. 566-571
  ISSN: 1862-5282
  DOI: 10.3139/ijmr-2005-0101
• Kümmel F., Magnier A., Wu T., Niendorf T., Höppel HW.:
  Residual Stresses in Ultrafine-Grained Laminated Metal Composites Analyzed by X-ray Diffraction and the Hole-Drilling Method
  In: Advanced Engineering Materials (2022)
  ISSN: 1438-1656
  DOI: 10.1002/adem.202200274
• Taali S., Toroghinejad MR., Kuglstatter M., Höppel HW.:
  Grain boundary engineering in roll-bonded copper to overcome the strength-ductility dilemma
  In: Journal of Materials Research and Technology 17 (2022), S. 3198-3204
  ISSN: 2238-7854
  DOI: 10.1016/j.jmrt.2022.02.032

2021

• Diepold B., Neumeier S., Meermeier A., Höppel HW., Sebald T., Göken M.:
  Temperature-Dependent Dynamic Strain Aging in Selective Laser Melted 316L
  In: Advanced Engineering Materials (2021)
  ISSN: 1438-1656
  DOI: 10.1002/adem.202001501
• Diepold B., Palm MS., Wimmer A., Sebald T., Höppel HW., Neumeier S., Göken M.:
  Rotating Scan Strategy Induced Anisotropic Microstructural and Mechanical Behavior of Selective Laser Melted Materials and Their Reduction by Heat Treatments
  In: Advanced Engineering Materials (2021)
  ISSN: 1438-1656
  DOI: 10.1002/adem.202100622
• Kohlhepp M., Uggowitzer PJ., Hummel M., Höppel HW.:
  Formation of Die Soldering and the Influence of Alloying Elements on the Intermetallic Interface
  In: Materials 14 (2021), S. 1580
  ISSN: 1996-1944
  DOI: 10.3390/ma14071580
• Kümmel F., Höppel HW., Göken M.:
  Ultrafine-Grained Laminated Metal Composites: A New Material Class for Tailoring Cyclically Stressed Components
  In: Advanced Engineering Materials (2021)
  ISSN: 1438-1656
  DOI: 10.1002/adem.202100070
• Matschkal D., Tuengerthal P., Lamm S., Göken M., Höppel HW., Felfer P.:
  Understanding the high creep resistance of mri 230d magnesium alloy through nanoindentation and atom probe tomography
  In: Metals 11 (2021), Art.Nr.: 1727
  ISSN: 2075-4701
  DOI: 10.3390/met11111727
• Pohl P., Kümmel F., Schunk C., Serrano-Munoz I., Markötter H., Göken M., Höppel HW.:
  About the role of interfaces on the fatigue crack propagation in laminated metallic composites
  In: Materials 14 (2021), Art.Nr.: 2564
  ISSN: 1996-1944
  DOI: 10.3390/ma14102564

2020

• Gulden F., Reinhold B., Gramstat S., Stich A., Tetzlaff U., Höppel HW.:
  Investigation of the run-in and corrosion behavior of a PEO-coated aluminum brake disc
  10th International Munich Chassis Symposium (Chassis.Tech Plus) (Munich)
  In: 10TH INTERNATIONAL MUNICH CHASSIS SYMPOSIUM 2019 (CHASSIS.TECH PLUS), WIESBADEN: 2020
• Höppel HW., Westermeyer M., Kümmel F., Göken M.:
  The Role of Interfaces on the Deformation Mechanisms in Bimodal Al Laminates Produced by Accumulative Roll Bonding
  In: Advanced Engineering Materials (2020)
  ISSN: 1438-1656
  DOI: 10.1002/adem.202000145
• Kalsar R., Yadav D., Sharma A., Brokmeier HG., May J., Höppel HW., Skrotzki W., Suwas S.:
  Effect of Mg content on microstructure, texture and strength of severely equal channel angular pressed aluminium-magnesium alloys
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 797 (2020), Art.Nr.: 140088
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2020.140088
• Wang YF., Huang CX., Fang XT., Höppel HW., Göken M., Zhu YT.:
  Hetero-deformation induced (HDI) hardening does not increase linearly with strain gradient
  In: Scripta Materialia 174 (2020), S. 19-23
  ISSN: 1359-6462
  DOI: 10.1016/j.scriptamat.2019.08.022

2019

• Bachmaier A., Hohenwarter A., Höppel HW., Ivanisenko J.:
  Nanostructured Metallic Materials and Composites: Processes, Properties and Microstructures
  In: Advanced Engineering Materials 21 (2019), Art.Nr.: ARTN 1801073
  ISSN: 1438-1656
  DOI: 10.1002/adem.201801073
• Glöckel F., Uggowitzer PJ., Felfer P., Pogatscher S., Höppel HW.:
  Influence of Zn and Sn on the precipitation behavior of new Al-Mg-Si alloys
  In: Materials 12 (2019), Art.Nr.: 2547
  ISSN: 1996-1944
  DOI: 10.3390/ma12162547
• Guillonneau G., Wheeler JM., Wehrs J., Philippe L., Baral P., Höppel HW., Göken M., Michler J.:
  Determination of the true projected contact area by in situ indentation testing
  In: Journal of Materials Research 34 (2019), S. 2859-2868
  ISSN: 0884-2914
  DOI: 10.1557/jmr.2019.236
• Schunk C., Nitschky M., Höppel HW., Göken M.:
  Superior Mechanical Properties of Aluminum-Titanium Laminates in Terms of Local Hardness and Strength
  In: Advanced Engineering Materials 21 (2019), Art.Nr.: ARTN 1800546
  ISSN: 1438-1656
  DOI: 10.1002/adem.201800546
• Zhou H., Huang C., Sha X., Xiao L., Ma X., Höppel HW., Göken M., Wu X., Ameyama K., Han X., Zhu Y.:
  In-situ observation of dislocation dynamics near heterostructured interfaces
  In: Materials Research Letters 7 (2019), S. 376-382
  ISSN: 2166-3831
  DOI: 10.1080/21663831.2019.1616330

2018

• Huang CX., Wang YF., Ma XL., Yin S., Höppel HW., Göken M., Wu XL., Gao HJ., Zhu YT.:
  Interface affected zone for optimal strength and ductility in heterogeneous laminate
  In: Materials Today 21 (2018), S. 713-719
  ISSN: 1369-7021
  DOI: 10.1016/j.mattod.2018.03.006
• Kümmel F., Diepold B., Prakash A., Höppel HW., Göken M.:
  Enhanced monotonic and cyclic mechanical properties of ultrafine-grained laminated metal composites with strong and stiff interlayers
  In: International Journal of Fatigue 116 (2018), S. 379-387
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2018.06.043
• Kümmel F., Diepold B., Sauer KF., Schunk C., Prakash A., Höppel HW., Göken M.:
  High Lightweight Potential of Ultrafine-Grained Aluminum/Steel Laminated Metal Composites Produced by Accumulative Roll Bonding
  In: Advanced Engineering Materials (2018)
  ISSN: 1438-1656
  DOI: 10.1002/adem.201800286
• Medvedev AE., Lapovok R., Koch E., Höppel HW., Göken M.:
  Optimisation of interface formation by shear inclination: Example of aluminium-cooper hybrid produced by ECAP with back-pressure
  In: Materials & Design 146 (2018), S. 142-151
  ISSN: 0264-1275
  DOI: 10.1016/j.matdes.2018.03.021
• Medvedev AE., Lapovok R., Koch E., Höppel HW., Göken M.:
  Optimisation of interface formation by shear inclination: Example of aluminium-copper hybrid produced by ECAP with back-pressure
  In: Materials & Design 146 (2018), S. 142-151
  ISSN: 0264-1275
  DOI: 10.1016/j.matdes.2018.03.021
• Merle B., Höppel HW.:
  Microscale High-Cycle Fatigue Testing by Dynamic Micropillar Compression Using Continuous Stiffness Measurement
  In: Experimental Mechanics 58 (2018), S. 465-474
  ISSN: 0014-4851
  DOI: 10.1007/s11340-017-0362-3
• Schunk C., Nitschky M., Höppel HW., Göken M.:
  Superior Mechanical Properties of Aluminum–Titanium Laminates in Terms of Local Hardness and Strength
  In: Advanced Engineering Materials (2018)
  ISSN: 1438-1656
  DOI: 10.1002/adem.201800546

2017

• Freund L., Giese S., Schwimmer D., Höppel HW., Neumeier S., Göken M.:
  High temperature properties and fatigue strength of novel wrought gamma/gamma' Co-base superalloys
  In: Journal of Materials Research 32 (2017), S. 4475-4482
  ISSN: 0884-2914
  DOI: 10.1557/jmr.2017.315
• Gulden F., Höppel HW., Göken M., Stich A., Gramstat S.:
  Fundamental Investigations of Aluminium Matrix Composite Brake Rotors for the Use in Passenger Cars
  In: EuroBreak 2017 (EB2017-MDS-026) 2017
• Höppel HW.:
  Ultrafine-grained Metals
  MDPI Basel, 2017
  ISBN: 978-3-03842-524-3
• Höppel HW., Goik P., Krechel C., Göken M.:
  Ex and in situ investigations on the role of persistent slip bands and grain boundaries in fatigue crack initiation
  In: Journal of Materials Research 32 (2017), S. 4276-4286
  ISSN: 0884-2914
  DOI: 10.1557/jmr.2017.313
• Kümmel F., Höppel HW., Göken M.:
  Layer architecture and fatigue life of ultrafine-grained laminated metal composites consisting of different aluminum alloys
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 702 (2017), S. 406-413
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2017.06.105
• Kümmel F., Tegtmeier TS., Höppel HW., Göken M.:
  Optimized layer architecture for an extended fatigue life of ultrafine-grained AA1050/AA5005 laminated metal composites
  In: IOP Conference Series: Materials Science and Engineering 194 (2017), S. 012036
  ISSN: 1757-8981
  DOI: 10.1088/1757-899X/194/1/012036
• Schwimmer D., Stich A., Höppel HW.:
  Possibilities for Improving the Heat Resistance of Cylinder Head Alloys based on AlSi7MgCu0.5 and AISi10MgCu0.5

2016

• Altieri-Weimar P., Yuan W., Annibale ES., Schoemaker S., Amberger D., Göken M., Höppel HW.:
  Reliability model of LED package regarding the fatigue behavior of gold wires
• Bach J., Möller J., Göken M., Bitzek E., Höppel HW.:
  On the transition from plastic deformation to crack initiation in the high- and very high-cycle fatigue regimes in plain carbon steels
  In: International Journal of Fatigue (2016)
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2016.04.003
  URL: http://www.sciencedirect.com/science/article/pii/S0142112316300512
• Kümmel F., Hausöl T., Höppel HW., Göken M.:
  Enhanced fatigue lives in AA1050A/AA5005 laminated metal composites produced by accumulative roll bonding
  In: Acta Materialia 120 (2016), S. 150-158
  ISSN: 1359-6454
  DOI: 10.1016/j.actamat.2016.08.039
• Kümmel F., Kreuz M., Hausöl T., Höppel HW., Göken M.:
  Microstructure and Mechanical Properties of Accumulative Roll-Bonded AA1050A/AA5005 Laminated Metal Composites
  In: Metals 6 (2016)
  ISSN: 2075-4701
  DOI: 10.3390/met6030056
• Ma X., Huang C., Moering J., Ruppert M., Höppel HW., Göken M., Narayan J., Zhu Y.:
  Mechanical properties of copper/bronze laminates: Role of interfaces
  In: Acta Materialia 116 (2016), S. 43-52
  ISSN: 1359-6454
  DOI: 10.1016/j.actamat.2016.06.023
• Nguyen H., Boehm W., Tsoupis I., Göken M., Höppel HW., Schmidt C., Hausöl T., Ruppert M., Merklein M.:
  Tailored heat treated accumulative roll bonded aluminum blanks: failure under bending stresses
  In: Production Engineering 10 (2016), S. 399-407
  ISSN: 0944-6524
  DOI: 10.1007/s11740-016-0685-4
• Ruppert M., Schunk C., Hausmann D., Höppel HW., Göken M.:
  Global and local strain rate sensitivity of bimodal Al-laminates produced by accumulative roll bonding
  In: Acta Materialia 103 (2016), S. 643-650
  ISSN: 1359-6454
  DOI: 10.1016/j.actamat.2015.11.009

2015

• Amberger D., Blickle T., Höppel HW., Göken M.:
  Fatigue behavior of calcium containing AZ91 magnesium alloys
  In: MP Materials Testing 57 (2015), S. 126-130
  ISSN: 0025-5300
  DOI: 10.3139/120.110694
• Höppel HW.:
  Ultrafine-Grained Metals
  In: Metals 5 (2015), S. 2393-2396
  ISSN: 2075-4701
• Prakash A., Nöhring WG., Lebensohn RA., Höppel HW., Bitzek E.:
  A multiscale simulation framework of the accumulative roll bonding process accounting for texture evolution
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 631 (2015), S. 104-119
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2015.02.005
• Ruppert M., Freund L., Wenzl T., Höppel HW., Göken M.:
  Ultrafine-grained austenitic stainless steels X4CrNi18-12 and X8CrMnNi19-6-3 produced by accumulative roll bonding
  In: Metals 5 (2015), S. 730-742
  ISSN: 2075-4701
  DOI: 10.3390/met5020730

2014

• Bach J., Höppel HW., Prell M., Göken M.:
  Crack initiation mechanisms in AA6082 fatigued in the VHCF-regime
  In: International Journal of Fatigue 60 (2014), S. 23-27
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2013.08.018
• Bösch D., Pogatscher S., Hummel M., Fragner W., Uggowitzer PJ., Göken M., Höppel HW.:
  Secondary Al-Si-Mg High-pressure Die Casting Alloys with Enhanced Ductility
  In: Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science 46 (2014), S. 1035-1045
  ISSN: 1073-5623
  DOI: 10.1007/s11661-014-2700-8
• Fragner W., Baumgartner K., Suppan H., Hummel M., Bösch D., Höppel HW., Uggowitzer PJ.:
  Using scrap in recycling alloys for structural applications in the automotive industry
  Light Metals 2014 - TMS 2014 Annual Meeting and Exhibition (San Diego, CA)
  URL: https://www.scopus.com/record/display.uri?eid=2-s2.0-84899827386∨igin=inward
• Fried M., Krechel C., Affeldt EE., Eckert B., Kimmig S., Retze U., Höppel HW., Göken M.:
  Fatigue crack initiation in nickel-based superalloys studied by microstructure-based FE modeling and scanning electron microscopy
  In: MATEC Web of Conferences 14 (2014)
  ISSN: 2261-236X
  DOI: 10.1051/matecconf/20141416001
• Marr T., Freudenberger J., Maier V., Höppel HW., Göken M., Schultz L.:
  The Strengthening Effect of Phase Boundaries in a Severely Plastically Deformed Ti-Al Composite Wire
  In: Metals 4 (2014), S. 37-54
  ISSN: 2075-4701
  DOI: 10.3390/met4010037
• Ruppert M., Höppel HW., Göken M.:
  Influence of cross-rolling on the mechanical properties of an accumulative roll bonded aluminum alloy AA6014
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 597 (2014), S. 122-127
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2013.12.075

2013

• Amberger D., Blickle T., Höppel HW., Göken M.:
  Fatigue Behavior of Calcium Containing AZ91 Magnesium Alloys
  In: T. Beck , E. Charkaluk E. (Hrsg.): Proceedings of the 7th International Conference on Low Cycle Fatigue 2013
  DOI: 10.3139/120.110694
• Bach J., Göken M., Bitzek E., Höppel HW.:
  Influence of specimen geometry on temperature increase during ultrasonic fatigue testing
  In: Ultrasonics 53 (2013), S. 1412-1416
  ISSN: 1874-9968
  DOI: 10.1016/j.ultras.2013.04.021
• Bach J., Höppel HW., Bitzek E., Göken M.:
  Influence of specimen geometry on temperature increase during ultrasonic fatigue testing
  In: Ultrasonics 53 (2013), S. 1412-1416
  ISSN: 0041-624X
  DOI: 10.1016/j.ultras.2013.04.021
• Bach J., Höppel HW., Bitzek E., Göken M.:
  Influence of specimen geometry on temperature increase during ultrasonic fatigue testing
  In: Ultrasonics 53 (2013), S. 1412-1416
  ISSN: 0041-624X
  DOI: 10.1016/j.ultras.2013.04.021
• Bach J., Liebig JP., Höppel HW., Blum W.:
  Influence of grain boundaries on the deformation resistance: Insights from an investigation of deformation kinetics and microstructure of copper after predeformation by ECAP
  In: Philosophical Magazine 93 (2013), S. 4331-4354
  ISSN: 0031-8086
  DOI: 10.1080/14786435.2013.828161
• Chekhonin P., Scharnweber J., Scharnweber M., Oertel C-., Hausöl T., Höppel HW., Jaschinski J., Marr T., Skrotzki W.:
  Mechanical properties of aluminium laminates produced by accumulative roll bonding
  In: Crystal Research and Technology 48 (2013), S. 532-537
  ISSN: 0232-1300
  DOI: 10.1002/crat.201300121
• Göken M., Hausöl T., Höppel HW.:
  Fatigue Life, Cyclic Deformation Behaviour and Damage Mechanisms of Ultrafine-Grained AA5754 Aluminum Alloy Produced by Accumulative Roll Bonding
  In: T. Beck , E. Charkaluk E. (Hrsg.): Proceedings of the 7th International Conference on Low Cycle Fatigue 2013
• Hoi Pang Ng ., Przybilla T., Schmidt C., Lapovok R., Orlov D., Höppel HW., Göken M.:
  Asymmetric accumulative roll bonding of aluminium-titanium composite sheets
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 576 (2013), S. 306-315
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2013.04.027
• Kommer M., Schwub S., Göken M., Höppel HW., Freudenberger J.:
  Cyclic Deformation Behaviour and Damage Mechanisms in CuAgZr Alloys
  In: T. Beck , E. Charkaluk E. (Hrsg.): Proceedings of the 7th International Conference on Low Cycle Fatigue 2013
• Kurtovic A., Niendorf T., Hausöl T., Höppel HW., Göken M., Maier HJ.:
  Surface strain evolution of ultrafine-grained aluminum alloy laminates under tension-Microscale plastic instabilities and the Portevin-Le Chatelier effect
  In: Scripta Materialia 68 (2013), S. 809-812
  ISSN: 1359-6462
  DOI: 10.1016/j.scriptamat.2013.01.036
• Kurtovic A., Niendorf T., Hausöl T., Höppel HW., Göken M., Maier HJ.:
  Surface strain evolution of ultrafme-grained aluminum alloy laminates under tension - Microscale plastic instabilities and the Portevin-Le Chatelier effect
  In: Scripta Materialia 68 (2013), S. 809-812
  ISSN: 1359-6462
  DOI: 10.1016/j.scriptamat.2013.01.036
• Niendorf T., Boehner A., Höppel HW., Göken M., Valiev RZ., Maier HJ.:
  Comparison of the monotonic and cyclic mechanical properties of ultrafine-grained low carbon steels processed by continuous and conventional equal channel angular pressing
  In: Materials & Design 47 (2013), S. 138-142
  ISSN: 0264-1275
  DOI: 10.1016/j.matdes.2012.12.025
• Ruppert M., Böhm W., Nguyen H., Höppel HW., Merklein M., Göken M.:
  Influence of upscaling accumulative roll bonding on the homogeneity and mechanical properties of AA1050A
  In: Journal of Materials Science 48 (2013), S. 8377-8385
  ISSN: 0022-2461
  DOI: 10.1007/s10853-013-7648-3

2012

• Boehner A., Niendorf T., Amberger D., Höppel HW., Göken M., Maier HJ.:
  Martensitic transformation in ultrafine-grained stainless steel AISI 304l under monotonic and cyclic loading
  In: Metals 2 (2012), S. 56-64
  ISSN: 2075-4701
  DOI: 10.3390/met2010056
• Böhner A., Höppel HW., May J., Göken M.:
  Influence of the ECAP processing parameters on the cyclic deformation behavior on ultrafine-grained cubic face centered metals
  In: Advanced Engineering Materials 14 (2012), S. 842-847
  ISSN: 1438-1656
  DOI: 10.1002/adem.201100217
• Chekhonin P., Beausir B., Scharnweber J., Oertel CG., Hausöl T., Höppel HW., Brokmeier HG., Skrotzki W.:
  Confined recrystallization of high-purity aluminium during accumulative roll bonding of aluminium laminates
  In: Acta Materialia 60 (2012), S. 4661-4671
  ISSN: 1359-6454
  DOI: 10.1016/j.actamat.2012.04.004
• Chekhonin P., Beausir B., Scharnweber J., Oertel CG., Jaschinski J., Hausöl T., Höppel HW., Brokmeier HG., Skrotzki W.:
  Mechanical anisotropy of aluminium laminates produced by ARB
  In: Materials Science Forum 702-703 (2012), S. 151-156
  ISSN: 0255-5476
  DOI: 10.4028/www.scientific.net/MSF.702-703.151
• Göken Mathias, Höppel Heinz Werner, Hausöl Tina, Bach Jochen, Maier Verena, Schmidt Christian W., Amberger Dorothea:
  Grain refinement and deformation mechanisms in heterogeneous ultrafine-grained materials processed by accumulative roll bonding
  Proceedings of the 33rd Risø International Symposium on Materials Science
  In: Nanometals - status and perspective 2012
• Göken M., Höppel HW., Hausöl T., Bach J., Maier V., Schmidt C., Amberger D.:
  GRAIN REFINEMENT AND DEFORMATION MECHANISMS IN HETEROGENEOUS ULTRAFINE-GRAINED MATERIALS PROCESSED BY ACCUMULATIVE ROLL BONDING
• Hausöl T., Höppel HW., Göken M.:
  Ultrafine-grained AA6014/AA5754 laminates produced by accumulative roll bonding (ARB)
  In: Materialwissenschaft und Werkstofftechnik 43 (2012), S. 334-339
  ISSN: 0933-5137
  DOI: 10.1002/mawe.201200950
• Hausöl T., Schmidt C., Maier V., Böhm W., Nguyen MH., Merklein M., Höppel HW., Göken M.:
  Formability of ultrafine-grained AA6016 sheets processed by accumulative roll bonding
  In: Key Engineering Materials 504-506 (2012), S. 575-580
  ISSN: 1013-9826
  DOI: 10.4028/www.scientific.net/KEM.504-506.575
• Höppel HW., Pippan R., Motz C., Le Bourhis E.:
  Nanostructured materials
  In: Advanced Engineering Materials 14 (2012)
  ISSN: 1438-1656
  DOI: 10.1002/adem.201200306
• Höppel HW., Pippan R., Motz C., Le Bourhis E.:
  Nanostructured Materials
  In: Advanced Engineering Materials 14 (2012), S. 941-941
  ISSN: 1438-1656
  DOI: 10.1002/adem.201200306
• Maier V., Hausöl T., Schmidt C., Böhm W., Hung Nguyen ., Merklein M., Höppel HW., Göken M.:
  Tailored heat treated accumulative roll bonded aluminum blanks: Microstructure and mechanical behavior
  In: Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science 43 (2012), S. 3097-3107
  ISSN: 1073-5623
  DOI: 10.1007/s11661-012-1151-3
• Schaufler J., Durst K., Haas T., Nolte R., Höppel HW., Göken M.:
  The influence of hydrogenated amorphous carbon coatings (a-C:H) on the fatigue life of coated steel specimens
  In: International Journal of Fatigue 37 (2012), S. 1-7
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2011.09.008
• Schmidt C., Ruppert M., Höppel HW., Nachtrab F., Dietrich A., Hanke R., Göken M.:
  Design of graded materials by particle reinforcement during accumulative roll bonding
  In: Advanced Engineering Materials 14 (2012), S. 1009-1017
  ISSN: 1438-1656
  DOI: 10.1002/adem.201200046
• Yasir M., Mori G., Wieser H., Reller A., Höppel HW.:
  Study of sensitization and different heating cycles on stainless steels used for automotive exhaust components
  In: Materials and Corrosion-Werkstoffe und Korrosion 63 (2012), S. 763-776
  ISSN: 0947-5117
  DOI: 10.1002/maco.201106255

2011

• Boehner A., Maier V., Durst K., Höppel HW., Göken M.:
  Macro- and nanomechanical properties and strain rate sensitivity of accumulative roll bonded and equal channel angular pressed ultrafine-grained materials
  In: Advanced Engineering Materials 13 (2011), S. 251-255
  ISSN: 1438-1656
  DOI: 10.1002/adem.201000270
• Göken M., Höppel HW.:
  Fatigue behaviour in nanostructured metals
  Elsevier Ltd., 2011
  ISBN: 9781845696702
  DOI: 10.1533/9780857091123.3.507
• Göken M., Höppel HW.:
  Tailoring nanostructured, graded, and particle-reinforced Al laminates by accumulative roll bonding
  In: Advanced Materials 23 (2011), S. 2663-2668
  ISSN: 0935-9648
  DOI: 10.1002/adma.201100407
• Hausöl T., Höppel HW., Göken M.:
  Microstructure and mechanical properties of accumulative roll bonded AA6014/AA5754 aluminium laminates
  In: Materials Science Forum 667-669 (2011), S. 217-222
  ISSN: 0255-5476
  DOI: 10.4028/www.scientific.net/MSF.667-669.217
• Höppel HW., Göken M., May L., Prell M.:
  Influence of grain size and precipitation state on the fatigue lives and deformation mechanisms of CP aluminium and AA6082 in the VHCF-regime
  33 (2011), S. 10-18
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2010.04.013
• Höppel HW., Kriebel F., Lapovok R., Boehner A., Göken M.:
  Influence of backpressure during ECAP on the monotonic and cyclic deformation behavior of AA5754 and Cu99.5
  13 (2011), S. 269-274
  ISSN: 1438-1656
  DOI: 10.1002/adem.201000269
• Korn M., Lapovok R., Böhner A., Höppel HW., Mughrabi H.:
  Bimodal grain size distributions in UFG materials produced by SPD - Their evolution and effect on the fatigue and monotonic strength properties
  In: Kovove Materialy-Metallic Materials 49 (2011), S. 51-63
  ISSN: 0023-432X
  DOI: 10.4149/km-2011-1-51
• Maier V., Durst K., Müller J., Backes B., Höppel HW., Göken M.:
  Nanoindentation strain-rate jump tests for determining the local strain-rate sensitivity in nanocrystalline Ni and ultrafine-grained Al
  In: Journal of Materials Research 26 (2011), S. 1421-1430
  ISSN: 0884-2914
  DOI: 10.1557/jmr.2011.156
• Schmidt C.W., Knödler P., Höppel H.W., Göken M.:
  Particle based alloying by accumulative roll bonding in the system Al-Cu
  In: Metals 1 (2011), S. 65-78
  ISSN: 2075-4701
  DOI: 10.3390/met1010065
• Schmidt C., Höppel HW., Göken M.:
  Maßgeschneiderte partikelverstärkte Verbundwerkstoffe und Werkstoffverbunde hergestellt durch den akkumulativen Walzprozess (ARB)
  18. Symposium Verbundwerkstoffe
  In: Tagungsband zum 18. Symposium Verbundwerkstoffe 2011
• Schmidt C., Knieke C., Maier V., Höppel HW., Peukert W., Göken M.:
  Influence of Nanoparticle Reinforcement on the Mechanical Properties of Ultrafine-Grained Aluminium Produced by ARB
  In: Materials Science Forum 667-669 (2011), S. 725--730
  ISSN: 0255-5476
  DOI: 10.4028/www.scientific.net/MSF.667-669.725
• Schwarz W., Schwub S., Quering K., Wiedmann D., Höppel HW., Göken M.:
  Life prediction of thermally highly loaded components: Modelling the damage process of a rocket combustion chamber hot wall
  In: CEAS Space Journal 1 (2011), S. 83-97
  ISSN: 1868-2502
  DOI: 10.1007/s12567-011-0007-9

2010

• Brunner J., May J., Höppel HW., Göken M., Virtanen S.:
  Localized corrosion of ultrafine-grained Al-Mg model alloys
  In: Electrochimica Acta 55 (2010), S. 1966-1970
  ISSN: 0013-4686
  DOI: 10.1016/j.electacta.2009.11.016
• Hausöl T., Höppel HW., Göken M.:
  Microstructure and mechanical properties of accumulative roll bonded aluminium alloy AA5754
  In: Journal of Physics: Conference Series 240 (2010), Art.Nr.: 012128
  ISSN: 1742-6588
  DOI: 10.1088/1742-6596/240/1/012128
• Hausöl T., Höppel HW., Göken M.:
  Tailoring materials properties of UFG aluminium alloys by accumulative roll bonded sandwich-like sheets
  In: Journal of Materials Science 45 (2010), S. 4733-4738
  ISSN: 0022-2461
  DOI: 10.1007/s10853-010-4678-y
• Hausöl T., Maier V., Schmidt C., Winkler M., Höppel HW., Göken M.:
  Tailoring materials properties by accumulative roll bonding
  In: Advanced Engineering Materials 12 (2010), S. 740-746
  ISSN: 1438-1656
  DOI: 10.1002/adem.201000044
• Höppel HW., Korn M., Lapovok R., Mughrabi H.:
  Bimodal grain size distributions in UFG materials produced by SPD: Their evolution and effect on mechanical properties
  DOI: 10.1088/1742-6596/240/1/012147
• Höppel HW., Prell M., May L., Göken M.:
  Influence of grain size and precipitates on the fatigue lives and deformation mechanisms in the VHCF-regime
  In: Procedia Engineering 2 (2010), S. 1025-1034
  ISSN: 1877-7058
  DOI: 10.1016/j.proeng.2010.03.111
• Maier V., Höppel HW., Göken M.:
  Nanomechanical behaviour of Al-Ti layered composites produced by accumulative roll bonding
  In: Journal of Physics: Conference Series 240 (2010), Art.Nr.: 012108
  ISSN: 1742-6588
  DOI: 10.1088/1742-6596/240/1/012108
• Mughrabi H., Höppel HW.:
  Cyclic deformation and fatigue properties of very fine-grained metals and alloys
  In: International Journal of Fatigue 32 (2010), S. 1413-1427
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2009.10.007
• Scharnweber J., Skrotzki W., Oertel CG., Brokmeier HG., Höppel HW., Topic I., Jaschinski J.:
  Texture, microstructure and mechanical properties of ultrafine grained aluminum produced by accumulative roll bonding
  In: Advanced Engineering Materials 12 (2010), S. 989-994
  ISSN: 1438-1656
  DOI: 10.1002/adem.201000067
• Skrotzki W., Scharnweber J., Oertel C-., Höppel HW., Topic I., Brokmeier H-., Jaschinski J.:
  Plastic anisotropy of ultrafine grained Al alloy AA6016 produced by accumulative roll bonding
  In: Solid State Phenomena 160 (2010), S. 171-176
  ISSN: 1012-0394
  DOI: 10.4028/www.scientific.net/SSP.160.171
• Vevecka-Priftaj A., Höppel HW., Göken M.:
  Deformation behaviour of nanocrystalline al alloy, processed by severe plastic deformation
  7th International Conference of the Balkan Physical Union (Alexandroupolis)
  DOI: 10.1063/1.3322399

2009

• Höppel HW., Mughrabi H., Vinogradov A.:
  Fatigue Properties of Bulk Nanostructured Materials
  John Wiley and Sons, 2009
  ISBN: 9783527315246
  DOI: 10.1002/9783527626892.ch22
• Saitova LR., Höppel HW., Göken M., Semenova IP., Raab GI., Valiev RZ.:
  Fatigue behavior of ultrafine-grained Ti-6Al-4V 'ELI' alloy for medical applications
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 503 (2009), S. 145-147
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2008.04.082
• Saitova LR., Höppel HW., Göken M., Semenova IP., Raab GI., Valiev RZ.:
  Fatigue behavior of ultrafine-grained Ti-6Al-4V 'ELI' alloy for medical applications
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 503 (2009), S. 145-147
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2008.04.082
• Saitova LR., Höppel HW., Göken M., Semenova IP., Valiev RZ.:
  Cyclic deformation behavior and fatigue lives of ultrafine-grained Ti-6AL-4V ELI alloy for medical use
  In: International Journal of Fatigue 31 (2009), S. 322-331
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2008.08.007
• Saitova LR., Höppel HW., Göken M., Semenova IP., Valiev RZ.:
  Cyclic deformation behavior and fatigue lives of ultrafine-grained Ti-6AL-4V ELI alloy for medical use
  In: International Journal of Fatigue 31 (2009), S. 322-331
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2008.08.007
• Saitova LR., Höppel HW., Göken M., Semenova IP., Valiev RZ.:
  Cyclic deformation behavior and fatigue lives of ultrafine-grained Ti-6AL-4V ELI alloy for medical use
  In: International Journal of Fatigue 31 (2009), S. 322-331
  ISSN: 0142-1123
  DOI: 10.1016/j.ijfatigue.2008.08.007
• Topic I., Höppel HW., Göken M.:
  Friction stir welding of accumulative roll-bonded commercial-purity aluminium AA1050 and aluminium alloy AA6016
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 503 (2009), S. 163-166
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2007.12.057

2008

• Dinkel M., Pyczak F., May J., Höppel HW., Göken M.:
  XRD profile analysis characterization of ultrafine grained Al-Mg alloys
  In: Journal of Materials Science 43 (2008), S. 7481-7487
  ISSN: 0022-2461
  DOI: 10.1007/s10853-008-2859-8
• Hueller M., Vlcek J., Dinkel M., Höppel HW., Göken M.:
  Hardening and thermal stability of nanocrystalline AlMg4.8 powder
  In: Philosophical Magazine 88 (2008), S. 1209-1226
  ISSN: 0031-8086
  DOI: 10.1080/14786430802089854
• May J., Amberger D., Dinkel M., Höppel HW., Göken M.:
  Monotonic and cyclic deformation behaviour of ultrafine-grained aluminium
  In: Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing 483-484 (2008), S. 481-484
  ISSN: 0921-5093
  DOI: 10.1016/j.msea.2006.12.177
• Mughrabi H., Höppel HW.:
  Assessment of fatigue damage in heterogeneous materials by application of a novel compliancen technique
  In: Solid Mechanics and Its Applications 152 (2008), S. 327-343
  ISSN: 0925-0042
  DOI: 10.1007/978-1-4020-8520-8-12
• Saitova L., Semenova I., Höppel HW., Valiev R., Göken M.:
  Enhanced superplastic deformation behavior of ultrafine-grained Ti-6Al-4V alloy
  In: Materialwissenschaft und Werkstofftechnik 39 (2008), S. 367-370
  ISSN: 0933-5137
  DOI: 10.1002/mawe.200800308
• Skrotzki W., Hünsche I., Hüttenrauch J., Oertel CG., Brokmeier HG., Höppel HW., Topic I.:
  Texture and mechanical anisotropy of ultrafine-grained aluminum alloy AA6016 produced by accumulative roll bonding
  In: Texture, Stress, and Microstructure 2008 (2008)
  ISSN: 1687-5397
  DOI: 10.1155/2008/328754
• Topic I., Höppel HW., Göken M.:
  Influence of rolling direction on strength and ductility of aluminium and aluminium alloys produced by accumulative roll bonding
  In: Journal of Materials Science 43 (2008), S. 7320-7325
  ISSN: 0022-2461
  DOI: 10.1007/s10853-008-2754-3
• Topic I., Höppel HW., Staud D., Merklein M., Geiger M., Göken M.:
  Formability of accumulative roll bonded aluminum AA1050 and AA6016 investigated using bulge tests
  In: Advanced Engineering Materials 10 (2008), S. 1101-1109
  ISSN: 1438-1656
  DOI: 10.1002/adem.200800167

2004

• Durst Karsten, Franke Oliver, Höppel Heinz Werner, Affeldt Ernst, Göken Mathias:
  Mikrostruktur und lokale mechanische Eigenschaften von platinmodifizierten Aluminidschichten auf Nickelbasis-Superlegierungen nach thermomechanischer Ermüdung
  Metallographietagung 2004 (Bochum)
  In: Prakt. Met. Sonderband 36, Frankfurt: 2004
• Höppel Heinz Werner, Göken Mathias, Klein Martin:
  Large chamber scanning electron microscopes: Challenges and Aspects for Materials Science
  In: Imaging & Microscopy (2004), S. 34-35
  ISSN: 1439-4243
• Göken M., Höppel HW., May J.:
  Enhanced strength and ductility in ultrafine-grained aluminium produced by accumulative roll bonding (ARB)
  In: Advanced Engineering Materials 6 (2004), S. 781-784
  ISSN: 1438-1656
• Neuner Frank, Nützel Ralf, Höppel Heinz Werner:
  Fretting fatigue of low carbon steels in the high cycle fatigue regime
  In: MP Materials Testing 46 (2004), S. 379-383
  ISSN: 0025-5300
• Höppel Heinz Werner, Kautz Martin, Xu Cheng, Barta-Schreiber Nicole, Langdon Terry G., Mughrabi Hael:
  Cyclic deformation behaviour and possibilities for enhancing the fatigue properties of ultrafine-grained metals
  NANOSPD2 (Wien)
  In: Proc. of the Conf. "Nanomaterials by Severe Plastic Deformation – NANOSPD2”, Weinheim: 2004
• Höppel Heinz Werner, Kautz Martin, Mughrabi Hael:
  Fatigue lives and cyclic deformation behaviour of ultrafine-grained metals and alloys
  DVM/DFG-Abschlusskolloquium "Lebensdauervorhersage” (Berlin)
  In: DVM/DFG-Abschlusskolloquium "Lebensdauervorhersage”, Berlin: 2004
• Höppel HW., Neuner F., Nützel R.:
  Fretting fatigue of low carbon steels in the high cycle fatigue regime
  LCF 5 (Berlin)
  In: 5th Int. Conf on Low Cycle Fatigue, Berlin: 2004
• Mughrabi Hael, Höppel Heinz Werner, Kautz Martin:
  Fatigue and microstructure of ultrafine-grained metals produced by severe plastic deformation
  In: Scripta Materialia 51 (2004), S. 807-812
  ISSN: 1359-6462
  DOI: 10.1016/j.scriptamat.2004.05.012

2003

• Höppel Heinz Werner, Neuner Frank:
  Untersuchung von mikrostrukturellen Einflussgrößen auf das Reibermüdungsverhalten und auf die Schädigungsmechanismen am Beispiel von Eisenbasislegierungen
  World of Dynamic Testing, (~)
  In: 10. Roell Amsler Symposium 2003 2003
• Mughrabi H., Höppel HW., Kautz M., Valiev R.:
  Annealing treatments to enhance thermal and mechanical stability of ultrafine-grained metals produced by severe plastic deformation
  In: Zeitschrift für Metallkunde 94 (2003), S. 1079-1083
  ISSN: 0044-3093
  DOI: 10.3139/146.031079

2002

• Zeschky Jürgen, Lo J.S.H., Scheffler M., Höppel Heinz Werner, Arnold Michael, Greil Peter:
  Polysiloxane-derived ceramic foam for the reinforcement of Mg alloy
  In: Zeitschrift für Metallkunde 93 (2002), S. 812-818
  ISSN: 0044-3093
• Biermann Horst, Christ Hans-Jürgen, Höppel Heinz Werner:
  Editorial in special issue of the ocassion of Prof. Mughrabi's 65th Birthday, Haël Mughrabi 65 years
  In: Zeitschrift für Metallkunde 93 (2002), S. 600-601
  ISSN: 0044-3093
• Höppel Heinz Werner, Valiev R.Z.:
  On the possibilities to enhance the fatigue properties of ultrafine-grained metals
  In: Zeitschrift für Metallkunde 93 (2002), S. 641-648
  ISSN: 0044-3093
• Höppel Heinz Werner, Eisenmeier G., Holzwarth B., Mughrabi Hael:
  Cyclic deformation and fatigue behaviour of the magnesium alloy AZ91: temperature effects and two-step fatigue tests
  In: Proc. of 8th Int. Fatigue Congress (FATIGUE 2002), West Midlands, UK: 2002
• Eisenmeier G., Höppel Heinz Werner, Ding Z.H., Mughrabi Hael:
  Ermüdungslebensdauer der Magnesiumlegierung AZ 91: Expriment und Modellierung
  2. DVM/DFG-Kolloquium Lebensdauervorhersage (Berlin)
  In: Mechanismenorientierte Lebensdauervorhersage für zyklisch beanspruchte metallische Werkstoffe 2002
• Höppel Heinz Werner, Zhou Z.M., Mughrabi Hael, Valiev R.V.:
  Microstructural study of the parameters governing coarsening and cyclic softening in fatigued ultrafine-grained copper
  In: Philosophical Magazine A (2002), S. 1781-1794
  ISSN: 0141-8610
  DOI: 10.1080/01418610210131399
• Kautz Martin, Höppel Heinz Werner, Zhou Z.M., Mughrabi Hael:
  Fatigue lives and cyclic deformation behaviour of ultrafine grained materials
  2. DVM/DFG-Kolloquium Lebensdauervorhersage (Berlin)
  In: Mechanismenorientierten Lebensdauervorhersage für zyklisch beanspruchte metallische Werkstoffe 2002
• Borbely A., Mughrabi Hael, Eisenmeier Gerd, Höppel Heinz Werner:
  A finite element modelling study of strain localization in the vicinity of near-surface cavities as a cause of subsurface fatigue crack initiation
  In: International Journal of Fracture 115 ( (2002), S. 227-232
  ISSN: 0376-9429
  DOI: 10.1023/A:1016350528652
• Ding H.-Z., Mughrabi Hael, Höppel Heinz Werner:
  A low-cycle fatigue life predication model of ultrafine-grained metals
  In: Fatigue & Fracture of Engineering Materials & Structures 25 (2002), S. 975-984
  ISSN: 8756-758X
• Eisenmeier G., Höppel Heinz Werner, Ding Z.H., Mughrabi Hael:
  Ermüdungslebensdauer der Magnesiumlegierung AZ91: Experiment und Modellierung
  In: Materialwissenschaft und Werkstofftechnik (2002), S. 238-243
  ISSN: 0933-5137

2001

• Höppel Heinz Werner, Brunnbauer M., Mughrabi Hael, Valiev R.Z., Zhilyaev A.P.:
  Cyclic deformation behaviour of ultrafine grain size copper produced by equal channel angular extrusion;
  ~ (Frankfurt)
  In: Materials Week 2000 Proceedings 2001
  URL: http://www.materialsweek.org/proceedings
• Eisenmeier G., Holzwarth B., Mughrabi Hael, Höppel Heinz Werner:
  Cyclic deformation and fatigue behaviour of the magnesium alloy AZ91
  In: Proc. of 12th Int. Conf. on Strength of Materials (ICSMA 12), Mat. Sci. Eng. A319-321: 2001